Leaking, Corroded, or Burst Pipes in Picayune, MS? Masters Plumbing Service Fixes It
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely β before opening drywall or digging β is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Picayune, MS use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
Acoustic & Thermal Leak LocationAll Pipe MaterialsPress-Fit & Sweat CapableLicensed in MS
Our Capabilities
What Separates Precision Pipe Repair from Guesswork
Our techs work on every pipe material found in Picayune, MS homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
π
Acoustic Leak Detection
Pressurized water escaping a pipe creates a characteristic acoustic signature. Our listening devices amplify ground and structure-borne sound to pinpoint a leak location within inches β through concrete slabs, behind drywall, or under flooring. This means we open only the section of wall, floor, or slab directly over the failure.
π‘οΈ
Thermal Camera Scanning
We use thermal imaging as a complement to acoustic detection β particularly useful for slab leaks and leaks inside insulated wall cavities where sound transmission is reduced.
π οΈ
All Pipe Materials & Joining Methods
Press-fit copper connections β particularly useful for repairs in occupied spaces where open flame is a concern β are available as an alternative to torch sweating where code permits.
π
Pressure-Tested Before We Leave
Every supply line repair is pressure-tested before we close the wall or floor. We pressurize the repaired section, hold the test pressure for the required duration, and confirm zero drop before considering the repair complete. You don't find out there's a second leak next week β we find it before we pack up.
Our Pipe Repair Services
Every Pipe Repair Type We Handle in Picayune, MS
Pipe failures have different causes depending on material type, age, water chemistry, and installation history. Here's how we address each category.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized β a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX β either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
Cross-linked polyethylene (PEX) is the current standard for residential supply piping. Failures are uncommon but occur at crimp or clamp fittings that were improperly installed, at pipe runs exposed to UV degradation, or at locations where the pipe was kinked during installation. We repair using expansion fittings (for PEX-A) or crimp fittings with the correct ring size for the pipe diameter.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
We also inspect upstream of the burst for additional sections that froze but haven't yet failed β because a partially-thawed line sometimes shows multiple failure points only after pressure is restored.
Slab Leaks
Under-Slab Pipe Leak Repair
Supply line leaks under a concrete slab are identified by acoustic detection and confirmed by thermal imaging. Once located, we evaluate three repair options: direct-access repair (jackhammering to the pipe, repairing the section, and patching the slab); rerouting the line through the wall framing above slab to bypass the failed underground run; or epoxy pipe lining for older copper systems with systemic pinhole corrosion.
Full Repipe
Whole-House Repipe Service
When galvanized supply lines are at end of life or polybutylene pipe (recalled for chronic failure) is in the home, a full repipe with PEX or copper is the permanent solution. We run new supply lines through the structure, transition all fixture connections, pressure test the entire new system, and patch access points in walls and ceilings.
We don't open walls at random. Acoustic and thermal detection tools tell us exactly where to cut before we pick up a saw.
1
Call & Describe β We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see β water stain on a ceiling, drop in water pressure, wet flooring β helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
This detection step routinely saves homeowners $500β$2,000 in unnecessary drywall removal compared to opening walls speculatively.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test β Then You're Done
Repair executes immediately on approval. After the repair, we repressurize and hold a pressure test to confirm the failure is fully resolved β not partially. The access opening is left clean for your drywall patch or left ready for your contractor.
Customer Reviews
What Picayune Customers Say About Our Pipe Work
β β β β β
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling β no torch in my wall β pressure tested, and patched the drywall themselves. Two hours total.
β N. Bergman, Picayune
β β β β β
Our galvanized supply lines finally gave out β low pressure everywhere, rust-colored water at some fixtures. Masters Plumbing Service repiped the whole house with PEX over two days. They confirmed pressure and flow at every fixture before leaving, patched all the wall access points smooth, and cleaned up each work area. One year later, no issues at all.
β O. & R. Adeyemi, Picayune, MS
β β β β β
I noticed my water meter spinning with all fixtures off β confirmed a leak in the supply system. Masters Plumbing Service ran a pressure test and acoustic scan, found a pinhole in a copper section under the slab in the utility room. They rerouted the line through the wall above slab, tested, and closed out the permit. The reroute was exactly the same cost as direct slab access would have been, but no damaged floor tile.
β F. Okoro, Picayune, MS
Common Questions
Pipe Repair FAQ for Picayune, MS Homeowners
Watch your water meter with all fixtures off. If the meter dial is moving or the leak indicator light is turning, water is escaping somewhere in your supply system. Other signs: unexplained increases in your monthly water bill, soft or discolored spots on walls or ceilings, mold or mildew smell in a room without a visible source, or a running sound inside walls when all fixtures are off.
In some cases β particularly for older copper systems with multiple pinhole failures along a supply run β rerouting the line through accessible framing rather than repairing it in place is more practical and more permanent. We present both options when they're both viable.
Repair options include direct slab access (jackhammer to the pipe, repair, patch), rerouting the supply line above slab through framing, and for copper systems with multiple pinhole failures, epoxy pipe lining from inside the pipe without excavation. We use acoustic and thermal detection to locate the leak before recommending a repair approach.
Galvanized pipe corrodes from the interior outward β by the time one section fails, the rest of the pipe is in varying stages of the same process. A localized repair buys time, but another section typically fails within 1β3 years if the system is at end of life. The honest answer is: it depends on how far along the corrosion is and how many sections are already narrowed or showing surface rust.
We don't rush pressure testing at the end. That's the step that confirms the repair is actually complete, and it takes the time it takes.
For slab access openings, we clean up concrete debris, complete the pipe repair, and patch the concrete. Tile or flooring restoration over a slab patch is normally a separate trade.
Service Area
Masters Plumbing Service Pipe Techs Serving Picayune, MS
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Picayune homes and businesses.
Precision Pipe Repair in Picayune, MS β We Find It Before We Cut
Active pipe leaks compound fast β mold growth can begin in 24β48 hours of sustained moisture. Masters Plumbing Service's pipe repair crew is in Picayune today, equipped with acoustic and thermal detection tools to find the failure precisely before anything is opened.
